Distribuiţi
Vezi subiectul anteriorIn josVezi subiectul urmator
avatar
gabilungu66
Membru avansat
MESAJE : 172
MEMBRU DIN : 12/06/2017
LOCATIE LOCATIE : Bucuresti

INFORMATIV O mica baza de date cu modalitati de intrare in SM

la data de Mier 13 Sept 2017, 17:21
Reputaţie mesaje: 100% (2 voturi)
TV Service Mode
Service mode for TV PHILIPS SAMSUNG SONY SANYO PIONEER ORION ChinaTv (Part 05)
Service mode for TV PHILIPS SAMSUNG SONY SANYO PIONEER ORION ChinaTv (Part 05)
Post under China TV, TV repair, TV Service Mode at 13:55
TV Service mode (part 05)

ORION ----- PHILIPS

ORION 28BDF TV790 (4400 chassis, processor SAA5297PS/262,
TDA8843, 8844). Vvimkuty power, hold the button "MENU" on the front panel until the LED light. Then turn on the remote control "STBY". To exit the service on account of new options - "MENU OFF" on the remote control.

ORION chassis 7000 7300 ORION LIFETECH LT-7500 processor uP83C055
Turn on the TV, hold button "MENU". Press the "SAT". Exit service mode - "TV".


ORION chassis BS990 CT63S92, CT71S92, FT5916 processor TVPOSM90.02/03
Press the button on the TV "OSD" "P-" "VOL-" and turn the power switch.

ORION chassis CODE A TV-3789F processor PCM195C30ECF0098, TDA2248, TDA8174A, FNI14B002
Press the "V-" on the front of TV and "6" on the remote, a little hold.
Contents of memory:
SECAM at 2A-F8
DK at 1D -41
You can use a "MAK-2000" code 1443.

ORION chassis CTS-AA TV 5176TX processor SAA5531PS/M4/0329
Sign in service menu:
Off TV Network button. Lock 7 foot lot on the processor. Enable TV. The screen in the lower left corner appears the letter S. Click on RECALL. To write to memory - press RECALL.
Exit service mode - turn off the TV Network button.

ORION chassis PCB8500 TV82301 SAA5667HL video processor. VSP9402
Press the button "MENU" on the front of the TV and hold the power switch. Exit - click "ST-BY", visit the IAC: Code 1097, "Shift + blue button.

ORION chassis T08-29K SPP2123F processor 8891CPBNG6KU3
0 Set the volume while pressing on the front of TV "VOL-" and DISP (rectangle) on the remote control.
Advanced service - in the section "F7 Page" put "1".
Switching pages - click on "MUTE" on the remote control.
Exodus - "MENU".

ORION chassis-processor TM8402A TV1470MJ OES6047V Videoprotsessory TB1226CN
To enter service menu you must click once on the remote control "9" on the TV and "VOL-".

ORION CTV222M processor TVPO2066-A41, chassis DIGIT2000, ORION KENDO UNIVERSUM 6325, 6325VT processor CCU2030.
Sign in service mode: short closed 15 and 23 feet KR1506HL1 in remote RC-4. Save your settings: You can use the remote ->.<- from TV "Horizon" with no graphics and click "SERVICE".
In service settings:
option1______ option2_______option3_______ option4
1: ON________ 1: OFF________1: ON _________1: OFF
2: ON _______ 2: OFF________ 2: OFF________ 2: ON
3: ON________3: ON _________3: ON _________3: OFF
4: OFF_______ 4: OFF_______ 4: OFF_________4: OFF
5: OFF______ 5: ON ________ 5: OFF_________5: OFF
6: OFF_______ 6: ON _______ 6: ON _________6: OFF
7: OFF_______ 7: OFF_______ 7: OFF________ 7: OFF
8: ON ________ 8: ON _______ 8: OFF_______ 8: ON
Go - POWER OFF

ORION MP2121U processor SDA555XFL. Videoprotsessory M61208
First ->.<- push button (two arrows meet separated horizontal stripe) or just FIX.
There's four entrances, though you need 9871, 9872, 9474, 9373. FIX button pressed before each set of figures. Output - 2 times "MENU".

ORION MP2927U. Processor VCT3833, sound MSP3413G
Click quickly "headphones" "--/--", "Headphones", "timer" - once in service menu.
Twice "menu" - geometry. R +, R-"Change," VOL + "," VOL-"- change the value. Save - "OK" immediately after the change.
Exit - to select "EXIT", press "OK."

ORION PLT7051 LCD 7 processor MTV512GMV, video T100A FP3797-1/3506TLDA2
TV - in dezhurnyy mode, and remote dial CH-> CH +> CH-> "MENU".

ORION TV2180MK6 processor OEC6027A
1. Switched on the TV hold the "VOL-" to a value of 0.
2. Off TV Network Network button.
3. Click on the front of the press "VOL-", not releasing it on the remote press "9" and hold them, turn on the TV and press the Network button on the front panel button "STAND BY".
Menu has two submenus.
Select items submenu is pressing the corresponding "license" klavish on the remote control. Control parameters are the keys "VOL + / -" or "-SET" on the remote control. Exit the submenu items and move from one submenu to another is the same combination: "VOL-" and, without releasing, press the remote key "9". Exit service menu is a choice item "8" in any submenu or by pressing the "POWER".

ORSON HINGWAH a chassis-VO CT-2120 processor ST6C-ELAINE2
From remote "SKIP", "VOL-", "FINE TUNE", "-". Selectable - PROGRAM

PACE PRIMAMSS100 MSS200 MSS500.
Entry: "MENU", "0", "STORE", "RIGHT ANOW", "LEFT ANOW"

PALLADIUM TV-100 chassis - see SCHNEIDER chassis DTV3, DTV4, TV17.

PALLADIUM Chassis PC100 765/325 765/368 765/384 processor ST92T93
Enable TV network switch, pressing the button "VOL +" and "VOL-". Press the POWER button on the remote control to exit - POWER OFF

PALLADIUM Processor TMP87PS38N "FO726XAC"
Sign in service: click on "VOL-" on TV and "DISPLAY" on the remote control.

PANASONIC Chassis AC1 TX-G10 / C
Install 60. Parameter SHARPNESS - at least. Press "OFF TIMER" control and hold, press the "V" on the keypad TV. Exodus - "NORMAL"

PANASONIC chassis APEDP264/266 APEDP264 CF27SF14/24/34V CT-31F24 CT-31XE24CV CT-F29992LV/W/XV - zakorotyty point FA1 and FA2 or pins 3 and 8 TP connector, located on-board A-board.
Exit: click button "ACTION" and "POWER" for 2 seconds.

PANASONIC chassis CP-185 TDA9381PS/N2/3I0785 MS9381/N2/3_DE1. Install the program in 1999, "Sharpness" = 0, press "MUTE" and "P-" on the front of TV and "Display" on the remote control.

PANASONIC chassis CP-521 TX-29PM1P processor TDA12021H1/N1D01.
Install 99. SHARPNESS parameter to a minimum. Press MUTE on the remote control and "V" on your keyboard TV.
Exit «Power OFF».

PANASONIC chassis CP-830FP TX-32PS12P processor SDA55xx
Install 99. SHARPNESS parameter to a minimum. Press MUTE on the remote control and "V" on your keyboard TV.
Exit «Power OFF».

PANASONIC Chassis EURO-1 EURO-2 E2100 TX-21AD2C TX-29A3C TX-25A3C TX-W28R3 TX-21MD1C TX-W28D1F processor CCU30001-05
Set the regulator "BASS" to "max", and regulator "TREBLE" to "min". Click on "F" on the TV. Press and hold "VOL-" on TV. Click "REVEAL" on the remote control. Exodus - "NORMAL"

PANASONIC Chassis EURO-2M, EURO-3, EURO-3H, EURO-3W, EURO-3HW, EURO-3HWS, TX-25AD50F TX-XD60C TX-W28/32/36D2DP/L processor SDA30C164 - press and hold "VOL-" Front and simultaneously press the remote REVEAL. In all variants instead of clicking REVEAL be RESET. Buttons RED (RED) and GREEN (GREEN) - move functions to service menu, YELLOW (YELLOW) and blue (BLUE) - modified the options button STORE - remember. Button NORMAL - exit the menu.

PANASONIC:
Chassis EURO-3 EURO-3H EURO-3W EURO-3HW EURO-3HWS TX-25AD50F TX-XD60C TX-W28/32/36D2DP/L processor SDA30C164,
Chassis EURO-4, EURO-4H TX-25LD4C, TX-28LD4C, TX-28PK25 processor SDA5450C48GE, SDA5450C59,
Chassis EURO-5 EURO-7ATX-25/28AD90F TX-32D5F ??-32PB50F / P:
Set the regulator "BASS" to max, and the regulator "TREBLE" to min. Click on "REVEAL" or "INDEX" button on the control (in all variants instead of clicking REVEAL be RESET), simultaneously press and hold the "VOL-" on TV. Exodus - "NORMAL"

PANASONIC Chassis EURO-10 TX-29PS1F
Set the regulator "BASS" to max, and the regulator "TREBLE" to min. Click on "F" on the TV. Press and hold "VOL-" on TV. Press the "INDEX" on the remote control. Exodus - "NORMAL"

PANASONIC chassis GAOO70 TX2170T processor MN152811TJN
Hold on TV "VOL-", click on the remote "screen with a plus.
Exodus - "NORMAL"

PANASONIC chassis GL1 TC-21GX10BS Protsescor TDA 12120H1/N100
Entry: "VOL-" = 0, timer = 30 minutes, RECALL on the remote and "VOL-" on TV. Edit menu - buttons "1" and "2". Navigating the menu buttons "3" and 4 ".
Exodus - POWER

PANASONIC chassis GLP22 TX-32LXD7 TX-32LED7F TX-26LXD7 TX-26LED7F
Sign in service: click and hold "- / V" on the front of TV, press 0 on the remote 3 times within 2 seconds.
To exit - EXIT button on the remote control.

PANASONIC chassis GP2A TX-29F250T, TX-29E220T, TX-29F155T, TX-29PM11P, TX-34P180T.
Log in menu «Service1» (geometry, RGB, sub.yaskravist):
Set Vol = 0, Timer = 30min (or 15 min), simultaneously press the button RECALL (on some models "DISPLAY" or "screen with a plus) button on the remote and" VOL-"on the front. To run the self press "VOL-" on the front and "Timer" on the remote control. Navigating the menu - red and green buttons, change settings - yellow and blue buttons. Memory write - "OK." Exodus - «NORMAL» .
Log «Service2»: Install 99-Channel. After logging in «Servise1», select «Sub-Brightness» and click on the remote «-/--». When you click in this mode «Display» is the entrance to the editor memory locations where you can manually edit the contents. Exodus - «NORMAL».

PANASONIC Chassis LH18 LCD TX-32LXD1
Sign-in-one service:
- Set up for BASS, TREBLE to minimum.
- Set the TV program on the number 99
- Click once "INDEX" button on the remote and "N" at the TV.
Log in Service-2 (option):
- Being in a service, press the green button on the remote repeatedly to select the last item of service menu JPEG VIEWER.
- Click on HOLD, open the Tools menu of options-2.
Buttons Red / Green to navigate up / down.
Buttons YELLOW / blue to change the values.
To remember to click STR changes separately for each item
To exit the service off in another mode.

PANASONIC chassis LH65A TC-32LX70/700, TC37LZ85, TC-32LX85
Sign in service: click and hold "VOL-" on the front of TV, press RECALL on the remote 3 times within 2 seconds.
To exit the Service mode - press the POWER button on the remote or on TV.

PANASONIC Chassis M17 TC-25GF10R, TX-33GF15P
1.Vstanovit volume = 0.
2. Press simultaneously "RECALL" button on the remote and "VOL-" on the front of the TV.

PANASONIC Chassis M18, M17W GAOO TX-29GF25T, TX-33, 29GF85T, TC-1924, 28WG12H, TX-29GF35T - simultaneously press the button "OFF TIMER" button on the remote and "VOL-" on the front of the TV. To adjust the memory device after replacement set jumpers TPA4, three output circuits connected to IC1213 "body" chassis, and then turning on the power. device enters the mode MARKET MODE.
Exit: After the end of the process remove the jumper.

PANASONIC chassis MD3N TX-29P190T SDA5555DM
Option 1: Set the BASS control to max, and TREBLE control to min. Press and hold "VOL-" on TV. Press the "INDEX" on the remote control. Exodus - "NORMAL".
Option 2: Install the program 99, press the HOLD button on the control.
Exit "NORMAL"
Option 3: OFF TIMER 30 min, and simultaneously push the button on the remote control "DISPLAY", on TV bar "VOL-".

PANASONIC chassis MX-1A TC-21E1R processor MN152810TTC4
Click on the main board TV service button S1101. Appears RNA. After the first key press can be adjusted (adjustment of brightness, contrast, saturation, volume and phase (horizontal alignment)). The second you click to regulate modes RGB. Exodus - "NORMAL"

PANASONIC chassis MX-1A TC-14L3R, TX-21LT3P TC/TX-14/21L3P, R; TC/TX-14/21LT3P, R, TC-21E1R processor MN152810TTC4
Enter: press the button on the main board S1101 "Service". The screen lights up white box with no inscriptions. Clicking on "Function" change control (brightness, contrast, saturation, volume, tone, balance the horizontal). Change Level option buttons "VOL +", "VOL-". The second button brings S1101 TV service in the second sub-mode control: the level of black R, G, B, swing signal R, G and thin horizontal line. Exodus - "NORMAL"

PANASONIC Chassis MX-2A, as for chassis MX-1A, TC-29V50R, processor MN152810TZN - click on the login button service switch S1101 (inside boards next to the switch vertical alignment). TV switch mode check, the screen appears CHK. Click on S1103 (FUN) to select the desired parameter adjustment. Exit - click S1101, or STAND BY and power off.

PANASONIC chassis MX-3 MX-3S TC-14F1, TC-F1D, TC-14L10R, TC1425RT, TC-20F1, TC-20L3R, TC-21F1T, TC-21L10R, TC21S10R, TC-2125RT, TC-2105RT, TX-2150T / TS, TC2150R, TC2150RM/RS, TC2170R / T processor MN152811TZT/TZX.
Hotel mode:
1. On the remote control - "OFF TIMER", the panel "CH UP" - enable.
2. On the remote control - "OFF TIMER", the panel - "VOL-" - disable.
Log in menu: Simultaneously press the "RECALL" button on the control and "VOL-" on the panel.
Exit - twice "NORMAL" on the remote control.

PANASONIC TX-29GF35T, TX-33GF85T, TX-29GF85T, TC-24WG12H, TC-28WG12H GAOO (option for chassis MX-3, MX-3C, MX-4S). Set Channel 60, TIMER = 30min and SHARPNESS - at least, and then click once button RECALL (on some models "DISPLAY" or "screen with a plus) in remote and VOL-button on the front of the TV. After replacing the memory device need initsializptsiya. To install this jumper TRA4 (contact 3 IC1213) to "ground". Turn the TV power. Apparatus enters the mode Market Mode. Memory write - key STR. Cofferdam after setting off.

PANASONIC Chassis MX-3V TC-14SV10S
Service for TV: Set the volume to zero. Press "MENU" and move the cursor to the position FEATURES. Press the OFF TIMER button and simultaneously press the right button on the control "RECALL" and "VOL-".
Tools for VCR: Set the volume to zero. Press "MENU" and move the cursor to the position FAETURES. Click the OFF TIMER. Just simultaneously press the right button on the remote cursor and "VOL-".

PANASONIC Chassis MX-4 TX-29V70T panel: TNQE145 TNQE147.
Hotel Mode: to cancel this mode, press the "VOL-" on your keyboard and TV OFF-Timer on the remote control.
Service menu:
1. set the volume 0.
2. Set the timer for 30 minutes.
3. Click RECAL on the remote and "VOL-" on TV keypad.
The screen shows RNA.
Select sub-menu buttons 1,2,3,4,5.
Exit from the menu - "NORMAL".

PANASONIC chassis MX-5 MX-5ATC-14D2, TC-2119R, TX-33GF15P, TC-25GF10R, TX-33GF15P, TC-20S2, TX-20S2T, TC-21Z2A, processor - MN1871681T,
Chassis MX-5Z TC-21D2Q processor TDA9381PS/N2/2I0905 N048Z, TDA9381PS/N2/2/0619 TDA9381N048M.
Set the volume on the TV equal "VOL-" = 0 and set the mode timer equal to 30 MIN. Then simultaneously press the CHANNEL UP button on the TV and RECALL on the remote control. Select sub -1, 2, 3, 4, 5. Exit - twice "NORMAL" on the remote

PANASONIC chassis MX-7 TC-21RM30RQ processor TDA 9384,
Chassis MX-7Z TC-15PM50R
Sign in service: set volume to "0" and the timer "30 MIN". The panel, press and hold "VOL-", and click on the remote control "DISPLAY" or "RECALL", (which looks like a screen plyusykom). Changing the menu buttons "1" and "2". Navigation through the menu buttons "3" and 4 ". Change "VOL +" and "VOL-". Exodus - POWER OFF

PANASONIC chassis MX-10 TX-29P80T
To log in to place the menu control with the following information: "SHARPNESS" of min, "VOLUME" of min, "BASS" to max, and "TREBLE" to min. At timer 30 min. Simultaneously press the button "Display" button on the control and "Vol-" on the front. Surcharge features - buttons 1-2-3-4, beginning - "NORMAL"

PANASONIC chassis MX-12 TX-29PS70T.
Entry: "VOL-" = 0, timer = 30 minutes, press RECALL on the remote and "VOL-" on TV.

PANASONIC NA8ML chassis - download details English description
PANASONIC NA8ML chassis - Download detailed english description
PANASONIC CT32SX31CE chassis NA8ML - menu select SET-UP CABLE, set the timer for 30 MIN, press ACTION three times to exit the menu, turn on channel 124, set the VOL = 0, the front panel press "VOL-", with on screen ' appear red inscription CHK. When lit this inscription, while pressing the front panel buttons "VOL +" and "ACTION" activated transition from service mode (red inscription CHK) setting mode to the default settings (CHK Yellow Label) .. If the yellow caption quickly press CHK button VOL + / VOL: - ", then the selected service option is normalized.
In service mode, you can also login zamknuvshy each control point FA1 and FA2 onboard TV.
If you press POWER on the remote selected group of parameters that are marked in the menu letters B, C .... E. To check purity of color need to press RECALL button on the remote control. To exit the service mode hold down the button for 2 seconds ACTION and POWER on the front. While TV is turned off and immediately turned on Channel 3. All previous settings disappear channel, channels need to adjust again.

PANASONIC CF-27SF14/24/34V CT-31SF24 CT-31XE24CV CT-F29992LV/W/XV Zakorotit point FA1 and FA2 or pins 3 and 8 TP connector located on board A-BOARD.

PANASONIC TX-25G10T (VOL) - at least, (TIMER) for 30min, press (VOL-) i (VOL +) on the front. Keys (1), (2) - choice of menu, CHK1-CHK4, (3), (4) - menu items, (VOL + / -) - Review.

PANASONIC Chassis Z5 TC14S1RCP, TX14S1TCC, TC21S1RCP, TX21S1TCC, TX21S1TCP processor MN152811TBS - click "OFF TIMER" on the remote and "VOL-" on TV. Click on STR for storing changes.
Exodus - "F"

PANASONIC chassis Z7 TX-21K1T / R, TX-21K2T, TX-14K1T, TC-14K1R, TX-14K2T, TX-21JTP3 processor SDA5254-A008
Select channel 60, set the "SHARPNESS" for min and simultaneously press the buttons "VOL-" and "OFF TIMER". Save values "STORE", exit "NORMAL"

PANASONIC chassis Z8 TX-21CK1 processor TDA9367PS/N1/4S0326, TX-29PM1P (chassis CP-521F).
Service - 1: select the channel 99, set the SHARPNESS at least. Press and hold the button on the remote control "MUTE". Press the TV button on the keyboard "V". Exodus - "NORMAL"
Sign in service - 2: being in a service, go to the line SUB-BRIGHT and press RECALL on the remote control.

PANASONIC Z-185 chassis TDA9381PS/N2/3I0785 MS9381/N2/3_DE1
select channel 99, set the SHARPNESS at least. Press and hold the button on the remote control "DISPLAY". Press the TV button on the keyboard "P-". Exodus - "NORMAL"

PANASONIC 2150: TIMER - in position OFF. Simultaneously press: on TV "VOL-", the remote "DISPLAY". Exodus - POWER OFF

PANASONIC AG-4700BY - simultaneous pressing forward, backward, and discard the cartridge.

PANASONIC TC21-GF80R - simultaneously press the "RECALL" button on the control and "VOL-" on the front of the TV. Exodus - NORMAL 2 times

PANASONIC TX-21JT1P
Select 60 channel set to SHERPNESS = 0 and simultaneously press the buttons "VOL-" on the front and "OFF TIMER" on the remote control. Save values - "STORE".

PATRIOT KM-2122 processor TDA 9381PS/N3/2/1830 delay in service menu:
One option - to lock the hidden button in the remote (if it CX3010 chip pins 11 and 25).
Option 2 - see the processor TDA9381-7NA.

PATRIOT KM-2111 / KM2112 / KM-2121 / KM-2131 / KM-2132A / KM-2135 / KM-2136 / KM-2138 / KM-2121 / Patriot KM-2911 / KM2912 / KM-2925 / HPC KM-2113 / HPC KM-2925 processor TDA9341PS/N3/A/1999, NTDA9341-2NDG
Sign in service - «MENU» «6", "4", "8", "3".
Select submenu - buttons "0 -4". Output - 2 times the button «Power» on the remote control.
Log in advanced service - «MENU» «6", "4", "8", "3», «Cal», «Lock», «5», «Cal», «Lock», «5.
Select submenu - buttons "0 -9.
Exit after initialization - «Power» «MENU» - «6", "4", "8", "3"

PHILIPS chassis A8.0. For memory initialization and close contact 904 9040. To enter service mode simultaneously press "VOL -" and "VOL +" panel TV. Exodus - STAND-BY

PHILIPSchassis Anubis S \ DD, 14GX123OA, 14RT235A, 14RT300A, 2OGX105O-855, 21GX1560-8568, 25GX1880-1985, 29GX1890-1995, 21RT118A, 21RT128A, 21RT129A, 21RT132A, 21RT1ZZA, 21RT137 A 21RT138A. Sign in service mode in contact closure M31 and M32 (land) near IC7710. Exodus - STAND-BY.

PHILIPS EM1A chassis, EM2E, EMZE, EM5E, ES.1E, FL, GFL, L04A, L04E, MD2.21E, MD2.22, MD2.25E, MG2.1E, MG3.1E, MG3.2E, MG4.1E, MG5 .1 E, MG7.1E, 28RT71O6, 28RT715, 28RT72O6, 28RT73O6, 28PW8206, 28PW8506, 29RT8OO6, 28RT83O6, 29RT8346, 29RT85O7. 29PT8509, 29RT86O7, 29RT9007, 29RT9O47, 32PW8206, 32PW8406, 32PW8506, 82WA8416, 7OTA7216, 70WA8416),
chassis TE1.1E 14PT1347/01, 14PT1547/01, 20PT1547/01, 37TA1437/03, 37PTB1347/19,
chassis DPTV325 43PP8320, 43PP8420, 43PP8421, 46PP8621, 50PP8421, 55PP8620.
To enter the service menu: with remote fast (up to 4 seconds) to enter with control numbers 062 596 i press "i +" (mode SAM, Service Alignment Mode), or press "MENU" (mode SDM, Service Default Mode, to set the initial values of some parameters useful for the measurement of control points), while in the service menu allowed switching applications. In the right corner z'vytsya inscription DILLER, or SAM, or SDM.
In standby SDM regular menu is available, it appears when you press the button "MENU". Button "INDEX" turns-off mode OSD. For the transition to the SAM using the buttons "VOL +" and "VOL-" on the front and hold not less than 4 seconds. To exit the SDM or SAM mode power off.
Navigation in both modes - buttons "UP / DOWN".

PHILIPS chassis D16-II, 25DC2660, 28DC2070, 28DC2670 80S31 processor to initialize memory - hold button on the TV "VOL +" and "P +", turn the power switch. For service mode to lock the control points M30 and M31. Exodus - TV.

PHILIPS chassis D2-MAC, EUROCRYPT BBD-901
Sign in service: disable the network, press and hold button "+" and "-" on the front panel, turn on the network. Memorization of any change - through the "OK". Exodus - "STANBY"

PHILIPS Chassis D2-MAC, EUROCRYPT BDE-353
Sign in service: the buttons on the remote control in sequence: [TV DEC] [P +] [P-] [CLOCK-BUTTON] [I-II].
Memorization of any change - through the "OK". Exodus - "STANBY"

PHILIPS chassis E-6, 28PT4505 processor SAB-C502-2R20N
On TV and in the operating dial on the remote "TV" "i" "STOP", beginning - "STANBY"

PHILIPS Chassis FL1.10, 25PV7505 25SL550 33PT700A/712A processor SAB8032,
chassis FL1.7 28ML8600/00B processor SAB8032.
1. To lock the memory initialization point S24 S25 located on the board SSP. On the remote press "MENU", "Blue", "red", "MENU", "MENU OFF".
2. To activate the lock mode SERVICE MODE control points S23 and S24, located on the motherboard SSP, exit - STAND-BY

PHILIPS chassis GR2.2 AA, 25PT400/42, 25PT410A/42, 28PT400A/42, 28PT450A/42. processor TMP47C1637. Lock contacts M33 and M34 (service) and hit INSTALL in the panel on the power. Inscription appears SER. To exit - on STANDBY.

PHILIPS chassis L01H.2E/AA, 14HT3304/01, 21HT5404/01Z processor TDA9552E, remote PC2882. Sign in service - 024 995 press "MENU" button or 062 596 "i", is another way to enter the service jumper zakorotyty 9631 and 9641. then turn on the TV button POWER. Code for lifting HOTEL - 319 753 and MUTE button

PHILIPSchassis L01.1E.L01.2E, 25RT4107, 21RT5306, 24PW6006, 25RT4457, 25RT5107, 25RT5506, 32PW5407, 32PW6006, 63TA5216, 70WA6216. 82PW6216 Service menu: while in the user menu, click on the remote control: Cursor up, down, left, right.

PHILIPS Chassis L6.1, 21PT1342 processor TMP47C1637N, SAA5290,
chassis L6. 1 AA, 14PT-1432/43, 14PT-1352/00/01/05/07/11/39, 14,20 PT-1542/01/43, 14PT-1552/00/01/05/11, 20PT- 1342/43, 21PT-1532/58, 37TA-1232/03, 37TA-1432/03, 37TA-1462/18, 37TA-1473/18, 52TB-2452/19, M-2052/00/01, M- 2152/00 / 07/15, M-2182/00, M-M192/05,
Chassis L6.2 20PT1353 processor SAA5290ZP/039/040/055 - closed contacts S1 and S2 on the processor (14 output circuits IC7600).

PHILIPS Chassis L6.2, 25PT4423 processor TDA9351
Remote control mode off once, then symknuty power when the LED goes out, turn on power while holding down the button "text" on the remote control.

PHILIPS chassis L6.2AA, 25PT4103/60 processor SAA5290ZP/040
Close control points "0053" and "0054" near the processor. Exodus - "STANBY"

PHILIPSChassis L7.1A, 14PT-118A \ 50B \ 67R \ 94R, 14PT132A \ 50B \ 50R \ 75R, 14PT133A \ 162R, 14PT137A \ 162R, 14PT138A \ 54R \ 58T \ 67R \ 71R \ 74R \ 75R \ 93S, 20PT188A \ 50B \ 67R \ 73R, 20PT120A \ 78R, 20PT132A \ 75R, 20PT137A \ 62R, 20PT138A \ 50D \ 58R \ 58H \ 58R \ 67R \ 71R \ 73R \ 74R \ 75R \ 94R \ 97R. Zakorotit contacts M24 and M25 on-board (PCB) and on the power. Out of service - click on STAND-BY. Attention error buffer is cleared!

PHILIPS L9.1E chassis, L9.2A, 14RT2665/00 21PT1354/58C 21PT1654/58 21PT3882/59R 25PT5307 processor SAA5542
Sign in service menu: "0" "6" "2" "5" "9" "6" "MENU"; to log on to the geometry (non-SAM) simultaneously press the "VOL-" and "PR-" Panel TV . Attention! SDM function in AS OFF does not turn on, or (perhaps) your TV stop working. Exodus - "STANBY"

PHILIPS Chassis L6.1, 14PT1322, 14PT1323, 14PT1332, 14PT1342, 14PT1352, PT1353, 14PT1363, 14PT1372-374, 14PT1532-1553, 14PT1562-1563, 14PT1573-1574, 14PT2663, 14PT2683-2594, 20PT1342, 20PT1352, 20PT1353, 20PT1542-1553 , 21PT1342, 21PT1532, 21PT1542, 21PT2563-2584, 37TA1220, 37TA1232, 37TA1262-1263, 37TA1273, 37TA1432.37TA1462-1463, 37TA1473, 37TB1252, 51TA1232.51TA1262, 51TA1462, 51TA1472, 51TB1222, 51TB1252, 51TB1452, 52TA1262, 52TA1420-1462 , 52TA1472, 52TB1252, 52TB1452, 2TB2452, M1432-2052, 1932 M21, M21 and all the 52-2192 model chassis L6.2. Method 1 - closed contacts S1 and S2 on the processor (14 output circuits IC7600).
Method 2 - on the remote control model RC7150 service click on DEFAULT or ALIGN.

PHILIPSChassis L9.2A, L9.2E, 14RT1582, 14RT1782, 14RT314A / B-3822 14RT3722, 14RT414A, 20RT1582, 20RT1782, 20RT224V, 20RT324A / B-3882 20RT3722, 20RT424, 20RT524A, 21RT1532, 21RT1 582 21RT334A, 21PT3382, 21RT3722885, 21PT534A, 14RT1345, 14RT1354, 14RT1365, 14RT1565, 14RT2665, 14RA01, 17RT1564-1565, 20PR1 554, 20RA01, 20TA01, 21RT1364, 21RT1654, 21RT1664, 21RT1865-2265, 21RT2664-2665, 21RT2684, 21RT4255, 21RT4355, 21RT4455, 21RT4475, 21RT4655, 37TA1274, 37TV1254, 52TA1464, 52TA1474, 52TA441 5 52TV1454, 52TV4395 Press the MUTE button on the remote and no later than 4 seconds, R-, R +, VOL-, VOL + on the front of the TV.

PHILIPS chassis MD1.1E 25PT4301, 25PT4501/60 TMP87CM36N-3270 processor, chassis MD1.2E, 24PW6322, 25RT4503, 25RT4513, 25RT4523, 25RT5123, 25RT5302, 25RT5322, 25RT5403, 25RT5424, 25RTB322, 28DW6734, 28RT4503, 28RT4513, 28RT4523, 28PW6202, 28PW6302 , 28PW6312, 28PW6322, 28PW6332, 29RT5123, 29RT5302, 29RT5322, 29RT5403, 29RT5423-5424, 29RT6413, 29RT6433, 29RT6773, 29RT8001-8005, 29RT8304, 29RT8344, 29RT9005-9006, 29RT9015, 29RT9046, 29RT9055, 29RT9113, 32DW6834, 2PWB302, 32PW6312 , 32PW6322, 32PW6332, 52TA4311, 63TA5213, 70WA6213, 70WB6193, 72TA5213, 82WA6213, 82WB6193. For service mode to lock contacts S42 and S43. Then click on the front of the TV at the same time "MENU" "P-". TV goes to standby SAM, if there are no mistakes and failures in the top row will be zero. Changes are automatically stored. Exodus - POWER OFF button on the control.

PHILIPS chassis MD2.11/12/13 - entrance is via a special menu control RC7150.

PHILIPS MD2.22E 25PT8303 Chassis
Simultaneously press the "?" and "SLEEP" under cover. Exodus - POWER OFF

PHILIPSchassis MG2.1E, 24PW8504, 25RT7304, 25RT8304, 28RT7104, 28RT7155, 28RT7204, 28RT7304, 28RT7404, 28PW8504-8505, 28PW9505, 28PW9515, 28PW9545, 29DS100, 29RT8001 -8005, 29RT8304, 29RT8344, 29RT9005-9006, 29RT9015, 29RT9046, 29RT9055 , 32PW8504-8505, 32PW8604, 32PW8806, 32PW9515, 32PW9523, 32PW9534-9535, 32PW9556, 2PW9566, 82WA8414 Press MUTE on the remote control and no later than 4 seconds "MENU" on the front of the TV. Also possibilities:
Mode SAM - closed for a second contacts 1 and 2 connector 0356 which is on SSP.
Mode SDM - closed for a second contacts 2 and 3 of connector 0356 that is on the SSP.

PHILIPS chassis MG3.1E 28PW9525 28PW8806 28PT7306/58
Type of remote combination. Then press "MENU" or "i". Presented several variants of code combinations.
"0" "6" "2" "5" "9" "6"
"0" "3" "6" "2" "5" "9" "6"
"0" "4" "6" "2" "5" "9" "6"
"0" "7" "6" "2" "5" "9" "6"
"0" "8" "6" "2" "5" "9" "6"
"0" "3" "6" "5" "9" "6"

PHILIPS 21PV288/58S EPSILON. To enter service mode to hold the PLAY button on the "TV" button "STOP" on the remote control about 5 seconds. Exit - click on "StandBy" console.

PHILIPS 14PV100/01 14PV505/58 processor SAA5541PS/M5/0194. Sign in service mode by the standby mode. You must simultaneously pressing "PLAY" on the TV and press "STOP" button on the control, while retain about 10 seconds.

PHILIPS 28PT4456/00 processor SAA5564PS/M3/0/81. To enter the service to close contact: "GND" and "SMD-servise mode" and turn on the TV in the network that is open 5-15 seconds.

PHILIPS 25PT4104/58 - two modes of service:
1) SDM - close control points on the chassis GND and SDM.
2) SAM-dial on the remote control, without breaks, 062 596 [] button enable OSD.

PHILIPS - Hotel profiles:
In models 25PT400/42, 25PT410A/42, 28PT400A/42, 28PT450A/42 hotel mode is activated while pressing the button VOL + and P + on the front panel for several seconds while the program turned 38. Off by pressing VOL-and P-well program in 1938. Programme 38 seconds and used usually for hotel management regime.
Model R-131, R-132, R-133, R-165 (chassis AA5) - enable channel 38 (this is important for all models), then hold "MENU" on the front and SLEEP (or OSD) on the remote control at least 4 sec.
H + inscription means that the mode vimkneno, H-off.
In models 3146, CTT-H instead of clicking on "MENU" button is used SELECT.
In models 3121 and 3122 while clicking on INSTALL and P + on the front at the time, not less than 3 seconds then turn off the console and enable key P + or P-.
In models R-217, CV6014, CV6107 clicking on INSTALL front and SLEEP on the remote control.
In models CV6012, CV6018, CV6109, ANUBIS S (AA, BB, CC, DD) to enable the hotel to keep the regime on the front panel keys and the P-STORE least 3 seconds. enabled the program to 38. To turn off - key P + and VOL-(at least 3 seconds), and in some models - and to turn.
The model ANUBIS S DD (and some others), hotel mode is possible only when enabled by an option when enabled 246 and channel 40. Possible option: turn on INSTALL and P +, INSTALL off and VOL-.
The model G8 must select VIDEO 2 mode and within one second press on the remote and TELETEXT FEATURE. Put in the appropriate menu OFF.
The model G88 as well, but using the SOUND ONLY.
The model PV4.0 on channel 38 on the remote click "PICTURE MENU" and FEATURE within 1 sec. to turn the hotel and click the PICTURE mode and OSD to turn.
In models Chassis GR1-AX (8-button front panel) to select channel 38, the simultaneous pressing on for 4 seconds and STORE P + hotel mode switches, STORE and CONTROL + (or STORE and CONTROL-) off. For 3-button front panel - simultaneously press STORE on the front and SLEEPTIMER on the remote for 4 seconds, or SELECT on the front and SLEEPTIMER on the remote. Green Label 'H +' on the screen means that the hotel enabled mode, and 'H-' - disabled.
0 comments: on "Service mode for TV PHILIPS SAMSUNG SONY SANYO PIONEER ORION ChinaTv (Part 05)"


avatar
Florin Iordache
Administrator
MESAJE : 3574
MEMBRU DIN : 02/06/2017
LOCATIE LOCATIE : TARGOVISTE
Profesie : PASIUNE
http://depanatorul-tv.forumgratuit.ro

INFORMATIV Re: O mica baza de date cu modalitati de intrare in SM

la data de Mier 13 Sept 2017, 17:32
Va multumim foarte,foarte mult pentru aceasta mica baza de date cu modalitati de intrare in SM !

O zi superba va dorim in continuare !


avatar
Admin
Fondator
MESAJE : 6012
MEMBRU DIN : 02/06/2017
LOCATIE LOCATIE : Bucuresti
Profesie : Electronist
http://depanatorul-tv.forumgratuit.ro

INFORMATIV Re: O mica baza de date cu modalitati de intrare in SM

la data de Mier 27 Sept 2017, 10:35
For all listed procedures, start with TV on, in TV mode, unless otherwise instructed. After procedure is complete, unplug set and re-plug in to finish reset.

If more than one procedure is listed for a given manufacturer, try the different ones until you see which one works for your set.

Coby:****************************************-

Enter menu, hi-lite “audio” then enter 8893

mode/source 2580 select “other setting”,select “shipment” then yes, after it exits service menu you need to power set off.



Dynex ****************************************-

source/input 2580

hold vol down on tv and hold #1 button on remote, vol will jump to halfway and set shuts off. Turn back on have 1st time setup screen.

source/input 2580

menu 1999 (tv is on)



Element ****************************************

menu 0000

menu 1147


Haier ******************************************

pull up menu, hi-lite “audio” then enter 8893




Hisense *****************************************

In customer menu go to”Parental” enter 0000 then select”Clean All” then power the set off and back on and first time setup menu will be there.

For some models, same as above model except in menu it is labeled “Lock”



Insignia *****************************************-

input 2580 (tv is on)



Mitsubishi ****************************************

Menu 123 or menu 2470 (tv is on)



Panasonic

Hold vol- on TV, press and hold menu button on remote



Philips ******************************************

Push menu, select”Features”then select”current software info” push 062596-info on remote then push info again then red”initialize appears and changes color then complete. Push power button to exit

TV is on,push 062596-info on remote,then push info again, red”initialized”appears it turns green when completed, then push power button to exit

Polariod *****************************************-

Hold vol- and chan- or hold vol+ and chan+ (tv is on)



Proscan ******************************************

In customer menu go to setup,select parental control menu, enter 0000 then select “clear channel list”.



RCA *******************************************-

Menu 1147



Sanyo *******************************************

hold vol down on TV, press and hold #1 button on remote, vol will jump to halfway and set shuts off. Turn back on have 1st time setup screen.



Samsung *****************************************-

Mute 182 power (tv is off)
(On some models, Factory Reset is on this menu, on some, you must go into the “Options” submenu



Seiki ********************************************-

Menu 0000



Sharp ********************************************
(Note – On Sharp models, you will need to look through the menus to find the reset option)

menu 1999

menu, 3481

menu 1147

while holding vol– & input buttons on tv plug in set when “k” appears push vol– & chan-



Sony *********************************************

Hold “arrow up” on remote and push power button on tv (tv is on)




Symphony *****************************************-

Source/input 2580




Toshiba ******************************************-

on Menu, select “Installation”, then “System Information” press the right arrow button, (“System Information” will change to “Factory Reset” or something similar) follow on-screen instructions



Vision Quest ***************************************-
Source/input 2580



Vizio ********************************************

In customer menu under “Help” tab is Factory Default enter 0000



Vestel (most):
Menu 4725 then select "RESET"

Samsung (European):
Power off, Info - Menu - Mute - Power, then find factory reset and execute option.

LG/Zenith:
Hold MENU on TV and MENU on remote for 5~10 seconds, then select reset option.

NEC:
While powering on hold "MENU" or "INPUT" on TV, depending on model. (Only disables error lock out/buffer and puts TV in temporary service mode.)
To reset to factory, on remote, Off Timer - Menu - Exit - Off Timer, then select reset option.




Lamp Error Reset for Sharp LCD TV.

With power LED off (TV in fake standby or AC power plug removed) hold Vol- and SOURCE/INPUT.

Power on the TV. Do not release the buttons.

This may take up to 20 seconds.

Look for a letter "K" on the side of the screen when it powers up. If this appears, continue. If not, repeat the above procedure.

Press CH- and VOL- to access service menu. See if LAMP ERROR appears in listing. If so, then a reset procedure is necessary

Page through the menus looking for "L ERR RESET". Execute the option (highlight and press OK.)

Power off the TV (TV in fake standby or AC power plug removed)

Hold Vol- and SOURCE/INPUT.

Power on the TV. Do not release the buttons.

No "K" should appear.

Power off the TV.

The TV should now be fixed.


For a Hannspree HSG1075 (may work for other models)

To access the factory reset menus-

Using the factory remote:

- Turn TV on
- in quick sucession press input, 0, 2, 3, 6, 3, menu.
- go to initialize in the new menu that opens
- go to recall factory data
- enter





JVC
1.
-Press the {MENU} button and go to the User Menu screen, make sure
that the indicator (arrow) is pointed and highlights the "Picture Control".

- The buttons on top of the remote are set to TV & VCR respectively.

- Set sleep timer to "0" minutes and while it is displayed, simultaneously
press the {VIDEO STATUS} & {DISPLAY} buttons.

- The main service menu will be displayed with choices #1 through #9.
- Press one of the corresponding number keys to enter that menu.

- Use the {CH+} {CH-} buttons to navigate within a menu.
- Use the {VOL+} {VOL-} buttons to change the values.
- Use the {MUTING} button to memorize the changed value.
- Use the {BACK} button to exit the service menu.

2.
Turn the TV on.
Using the remote control:

- Press the {INFO} & {MUTE} buttons at the same time.
- The Service Menu will be displayed

- Use the number keys to select the category.
- Use the {VOL+} {VOL-} buttons to enter the category.
NOTE: Some models don't have category selection.
- Use the {CH+} {CH-) buttons to select item to be adjusted.
- Use the {VOL+} {VOL-} buttons to change values.
- Press the {INFORMATION} button to exit.

3.
Turn the TV on.
Using the remote control:

# Press {DISPLAY} & {PIC MODE} buttons at the same time.
# The Service Menu will be displayed

# Use the number keys to select the category.
# Use the {UP} {DOWN} buttons to enter a category.
# Use the {LEFT} {RIGHT} buttons to select items.
# Use the {UP} {DOWN} buttons to change values.
# Press the {DISPLAY} button twice to exit.

4.
# Press the {MENU} button.
# Select "Clock Set".
# Set clock to 3:21 AM and press "Start Clock".
# While a "Thank You" message is displayed on screen, press the {MUTE} and {MENU} buttons.
# The Service Menu will come up.
# Use {UP} {DOWN} to select items.
# Use {LEFT} {RIGHT} to change values.
# To exit, turn the TV Off.

MITSUBISHI
1.
# Using the remote control press:
{MENU} {0} {3} {5} {3} buttons.
{MENU} {0} {3} {5} {7} buttons.

# Then use {VIDEO} or {AUDIO} buttons to enter two different groups of adjustments.
# {VIDEO} and {AUDIO} steps along through the adjustments, and {+} {-} does the adjusting.
# Press the {ENTER} button to save the change.
# Press the {MENU} button twice to exit service menu.

2.
# Using the remote control press:
{MENU} {1} {2} {5} {7} buttons.
{MENU} {1} {2} {5} {9} buttons.
{MENU} {1} {3} {7} {0} buttons.

# Then use {VIDEO} or {AUDIO} buttons to enter two different groups of adjustments.
# {VIDEO} and {AUDIO} steps along through the adjustments, and {+} {-} does the adjusting.
# Press the {ENTER} button to save the change.
# Press the {MENU} button twice to exit service menu

3.
Using the remote control press:

{MENU} {2} {3} {5} {6} buttons.
{MENU} {2} {3} {5} {7} buttons.
{MENU} {2} {3} {5} {8} buttons.
{MENU} {2} {3} {5} {9} buttons.

* Then use {VIDEO} or {AUDIO} buttons to enter two different groups of adjustments.
* {VIDEO} and {AUDIO} steps along through the adjustments, and {+} {-} does the adjusting.
* Press the {ENTER} button to save the change.
* Press the {MENU} button twice to exit service menu.

4.
# Using the remote control press:
{MENU} {8} {2} {5} {7} buttons.

# Then use {VIDEO} or {AUDIO} buttons to enter two different groups of adjustments.
# {VIDEO} and {AUDIO} steps along through the adjustments, and {+} {-} does the adjusting.
# Press the {ENTER} button to save the change.
# Press the {MENU} button twice to exit service menu.



Mits VZ8 chassis Menus
Option menu, Menu 1270
Service Menu, Menu 1257
Convergence Menu, Menu 1259, 4 Fine,
5 Coarse, 6 Misc.

PANASONIC
Panasonic TV's after 1996 can be set to "Serviceman Mode" with the
following remote control sequence:

-select the SET-UP icon and select CABLE mode.
-select the TIMER icon and set the SLEEP timer for 30 minutes.
-press the ACTION button twice to get out of the menus.
-change to channel 124.
-adjust the volume to minimum (0).
-Hit the VOL down button on the TV itself (not on
the remote) and a red "CHK" should appear in the upper corner.
-press the ACTION and VOLUME DOWN buttons (again, on the
TV, not the remote) you will toggle between AGING and SERVICEMAN modes.

Select Serviceman mode. The POWER button on the remote control will
select one of the five Serviceman Adjustment modes.

The modes are:

B - Serviceman VCJ SUB Adjustments. These include sub-tint,
sub-color, sub-brightness, sub-contrast, colorkiller/ABL/gamma,
audio and video adjustment, and vertical size.

C - Serviceman VCJ Cut-off adjustments. These include Red, Green
and Blue cut-off, red and blue drive, automatic fine tuning
(AFT), RF AGC (RF gain control), horizontal center, beam limit,
etc.

S - Serviceman Options Adjustments. These involce the PIP and
clock.

M - Serviceman MTS (Stereo/SAP) adjustments.

CHK - the mode you first entered. Normal picture and sound, lets
you check things over and still have a hotkey into the
service menu.

There is one more adjustment that isn't in the five modes, it's
global. When in either the yellow or red CHK mode, you can press
RECALL on the remote control to enter the purity field check mode.
This lets you select a pure white, red, green, or blue screen. A
good thing to walk away from if you just want to temporarily freak
out the floor manager, but it will be fixed as soon as the TV is
turned off. Oh well.

To get out of Serviceman mode, press ACTION and POWER on the
receiver simultaneously for at least 2 seconds. The TV will momentarily
shut off and then comes back on.

----------------------------------------------------------
PE77U / PX75U / PX77U / PZ700U / PZ750U
PD60U / PX6U / PX60U / PX600U
PD50U / PX50U / PX500U :


* Hold down the {VOL -} button ON THE PLASMA TV.
* Press the {RECALL} button 3 times on the remote.
* The Service Menu will be displayed.
* Use {1} {2} on remote to navigate main menu items.
* Use {3} {4} on remote to navigate sub-menu items.
* Use {VOL+} {VOL -} on remote to change item value.
* Write down all values before changing
Once a value is changed, THE CHANGE IS MADE.
* Power off to exit service mode and save.
---------------------------------------------------------
PA25UP / PD25UP / PX25UP :


* Using the remote control:
* Press the {MENU} button.
* Set "Antenna A" to "Cable".
* Select "Timer" menu and set sleep timer to 30 min.
* Press {OK} twice to exit menus.
* Tune to channel 124.
* Press and hold {VOL -} button ON THE PLASMA TV.

"CHK" appears in on top-left corner followed by 5 letter/numbers
(which are the cumulative hours in hex numbers)

* While the "CHK" is displayed, press the {OK} and {VOL+} buttons
ON THE TV simultaneously to toggle between Modes:

Red "CHK" for Serviceman- Yellow "CHK" for Aging

* Press the {POWER} button on the remote to select one of the six
Serviceman Adjustments Modes.

A. MTS ADJUSTMENT
B. CLOCK ADJUSTMENT
C. VIDEO ADJUSTMENT
D. HDEF ADJUSTMENT
E. VDEF ADJUSTMENT
F. DAF ADJUSTMENT
G. OTHER ADJUSTMENT

* Press {CH+} {CH -} on the remote to select the settings
on each of Service Adjustment Modes.

Write down the original values before modifying anything.
It's easy to erroneously adjust the wrong item.

* Press {VOL+} {VOL -} on the remote to change values.
* Press the {POWER} button on the TV to exit the service menu.
---------------------------------------------------
PA20UP / PX20UP :


* Using the remote control:
* Press the {MENU} button.
* Press "Setup" menu.
* On "Mode" menu, select "Cable"
* Select "Timer" menu and set sleep timer to 30 min.
* Press {ACTION} twice to exit menus.
* Tune to channel 124.
* Press and hold {VOL -} button ON THE PLASMA TV.

"CHK" appears in on top-left corner followed by 5 letter/numbers
(which are the cumulative hours in hex numbers)

* While the "CHK" is displayed, press the {ACTION} and {VOL+} buttons
ON THE TV simultaneously to toggle between Modes:

Red "CHK" for Serviceman - Yellow "CHK" for Aging

* Press the {POWER} button on the remote to select one of the six
Serviceman Adjustments Modes.

A. MTS ADJUSTMENT
B. CLOCK ADJUSTMENT
C. VIDEO ADJUSTMENT
D. HDEF ADJUSTMENT
E. VDEF ADJUSTMENT
F. DAF ADJUSTMENT
G. OTHER ADJUSTMENT

* Press {CH+} {CH -} on the remote to select the settings
on each of Service Adjustment Modes.

Write down the original values before modifying anything.
It's easy to erroneously adjust the wrong item.

* Press {VOL+} {VOL -} on the remote to change values.
* Press the {POWER} button on the TV to exit the service menu.


PANASONIC
Panasonic TV's after 1996 can be set to "Serviceman Mode" with the
following remote control sequence:

-select the SET-UP icon and select CABLE mode.
-select the TIMER icon and set the SLEEP timer for 30 minutes.
-press the ACTION button twice to get out of the menus.
-change to channel 124.
-adjust the volume to minimum (0).
-Hit the VOL down button on the TV itself (not on
the remote) and a red "CHK" should appear in the upper corner.
-press the ACTION and VOLUME DOWN buttons (again, on the
TV, not the remote) you will toggle between AGING and SERVICEMAN modes.

Select Serviceman mode. The POWER button on the remote control will
select one of the five Serviceman Adjustment modes.

The modes are:

B - Serviceman VCJ SUB Adjustments. These include sub-tint,
sub-color, sub-brightness, sub-contrast, colorkiller/ABL/gamma,
audio and video adjustment, and vertical size.

C - Serviceman VCJ Cut-off adjustments. These include Red, Green
and Blue cut-off, red and blue drive, automatic fine tuning
(AFT), RF AGC (RF gain control), horizontal center, beam limit,
etc.

S - Serviceman Options Adjustments. These involce the PIP and
clock.

M - Serviceman MTS (Stereo/SAP) adjustments.

CHK - the mode you first entered. Normal picture and sound, lets
you check things over and still have a hotkey into the
service menu.

There is one more adjustment that isn't in the five modes, it's
global. When in either the yellow or red CHK mode, you can press
RECALL on the remote control to enter the purity field check mode.
This lets you select a pure white, red, green, or blue screen. A
good thing to walk away from if you just want to temporarily freak
out the floor manager, but it will be fixed as soon as the TV is
turned off. Oh well.

To get out of Serviceman mode, press ACTION and POWER on the
receiver simultaneously for at least 2 seconds. The TV will momentarily
shut off and then comes back on.

----------------------------------------------------------
PE77U / PX75U / PX77U / PZ700U / PZ750U
PD60U / PX6U / PX60U / PX600U
PD50U / PX50U / PX500U :


* Hold down the {VOL -} button ON THE PLASMA TV.
* Press the {RECALL} button 3 times on the remote.
* The Service Menu will be displayed.
* Use {1} {2} on remote to navigate main menu items.
* Use {3} {4} on remote to navigate sub-menu items.
* Use {VOL+} {VOL -} on remote to change item value.
* Write down all values before changing
Once a value is changed, THE CHANGE IS MADE.
* Power off to exit service mode and save.
---------------------------------------------------------
PA25UP / PD25UP / PX25UP :


* Using the remote control:
* Press the {MENU} button.
* Set "Antenna A" to "Cable".
* Select "Timer" menu and set sleep timer to 30 min.
* Press {OK} twice to exit menus.
* Tune to channel 124.
* Press and hold {VOL -} button ON THE PLASMA TV.

"CHK" appears in on top-left corner followed by 5 letter/numbers
(which are the cumulative hours in hex numbers)

* While the "CHK" is displayed, press the {OK} and {VOL+} buttons
ON THE TV simultaneously to toggle between Modes:

Red "CHK" for Serviceman- Yellow "CHK" for Aging

* Press the {POWER} button on the remote to select one of the six
Serviceman Adjustments Modes.

A. MTS ADJUSTMENT
B. CLOCK ADJUSTMENT
C. VIDEO ADJUSTMENT
D. HDEF ADJUSTMENT
E. VDEF ADJUSTMENT
F. DAF ADJUSTMENT
G. OTHER ADJUSTMENT

* Press {CH+} {CH -} on the remote to select the settings
on each of Service Adjustment Modes.

Write down the original values before modifying anything.
It's easy to erroneously adjust the wrong item.

* Press {VOL+} {VOL -} on the remote to change values.
* Press the {POWER} button on the TV to exit the service menu.
---------------------------------------------------
PA20UP / PX20UP :


* Using the remote control:
* Press the {MENU} button.
* Press "Setup" menu.
* On "Mode" menu, select "Cable"
* Select "Timer" menu and set sleep timer to 30 min.
* Press {ACTION} twice to exit menus.
* Tune to channel 124.
* Press and hold {VOL -} button ON THE PLASMA TV.

"CHK" appears in on top-left corner followed by 5 letter/numbers
(which are the cumulative hours in hex numbers)

* While the "CHK" is displayed, press the {ACTION} and {VOL+} buttons
ON THE TV simultaneously to toggle between Modes:

Red "CHK" for Serviceman - Yellow "CHK" for Aging

* Press the {POWER} button on the remote to select one of the six
Serviceman Adjustments Modes.

A. MTS ADJUSTMENT
B. CLOCK ADJUSTMENT
C. VIDEO ADJUSTMENT
D. HDEF ADJUSTMENT
E. VDEF ADJUSTMENT
F. DAF ADJUSTMENT
G. OTHER ADJUSTMENT

* Press {CH+} {CH -} on the remote to select the settings
on each of Service Adjustment Modes.

Write down the original values before modifying anything.
It's easy to erroneously adjust the wrong item.

* Press {VOL+} {VOL -} on the remote to change values.
* Press the {POWER} button on the TV to exit the service menu.
-----------------------------------------------------
PANASONIC LCDs / CRTs / RPTVs :

* Hold down the {VOL -} button ON THE TV.
* Press the {RECALL} button 3 times on the remote.
* The Service Menu will be displayed.
* Use {1} {2} on remote to navigate main menu items.
* Use {3} {4} on remote to navigate sub-menu items.
* Use {VOL+} {VOL -} on remote to change item value.
* Write down all values before changing
Once a value is changed, THE CHANGE IS MADE.
* Power off to exit service mode and save.


Model PT45LC12:

1. Press and hold Vol Dn on center panel and press recall button on remote until Work Mode is displayed on screen.
2. Press and hold Vol Dn on TV and Swap button button on remote until Factory Adjust is displayed on the screen
3. Use Channel Dn button to select Digital and press the Action button.
-------------------------------------------------------
PANASONIC PROJECTORS :
1.
* Press the {MENU} button.
* Go to "Options" menu.
* Highlight "OSD".
* Then press and hold the {ENTER} button,
until the Service Menu is displayed.
* Press the {MENU} button to exit.

2.
# Turn the Projector on.
# Press the {POWER} button.
# A "Power Off" confirmation will come up on screen.
# Then press {LEFT} {UP} {DOWN} {UP} {DOWN}
& {ENTER} buttons.

# The Service Menu will be displayed.
# To exit, turn the Projector Off.
----------------------------------------------------------
PLASMAS 8UK / 9UK:

* Hold down the {VOL -} button ON THE PLASMA DISPLAY.
* Press the {STATUS} button 3 times on the remote.
(Status button is the one above Setup button)
* The Service Menu (CAT) will be displayed.
(CAT = Computer Aided Test Menu)
* Use the cursors keys on the remote to select a mode.
* And press the Action key {} to access the menu.
* To exit each mode, press the {R} button.
* To exit the CAT menu, press the {STATUS} button.
* Press {POWER} button on the Plasma to exit the service mode.
--------------------------------------------------------
PLASMAS 3UY / 4UY / 5UY / 6UY / 7UY:

* Hold down the {VOL -} button ON THE PLASMA DISPLAY.
* Press the {STATUS} button 3 times on the remote.
(Status button is the one below Power button)
* The Service Menu (CAT) will be displayed.
(CAT = Computer Aided Test Menu)
* Use the cursors keys on the remote to select a mode.
* And press the Action key {} to access the menu.
* To exit each mode, press the {R} button.
* To exit the CAT menu, press the {STATUS} button.
* Press {POWER} button on the Plasma to exit the service mode.
----------------------------------------------------------
Philips Magnavox
# Press {0} {6} {2} {5} {9} {7} {INFO+} on the remote.
or
# Press {0} {6} {2} {5} {9} {7} {STATUS} on the remote.
or
# Press {0} {6} {2} {5} {9} {7} {MENU} on the remote.
or
* Press {0} {6} {2} {5} {9} {6} {INFO+} on the remote.
or
* Press {0} {6} {2} {5} {9} {6} {STATUS} on the remote.
or
* Press {0} {6} {2} {5} {9} {6} {MENU} on the remote.
or
* Press {0} {6} {1} {5} {9} {6} {MENU} on the remote.
or
* Press {0} {6} {1} {5} {9} {7} {MENU} on the remote.
or
* Press {1} {6} {2} {5} {9} {6} {MENU} on the remote.
or
* Press {1} {6} {2} {5} {9} {6} {STATUS} on the remote.

* Turn the TV off to exit the Service Menu.

---------------------------------------------------------
* With the TV off:

* Press {0} {6} {2} {5} {9} {6} {STATUS} on the remote.

* Turn the TV off to exit the Service Menu.


PIONEER
PDP-4214

* Press the {INPUT} button on the remote.
* The input list will come up.
* Then press the {0} {9} {1} {7} buttons on the remote.
* To exit, press the {EXIT} button on the remote.

You can also press the back button when you are
in each category to get back to the main menu.

--------------------------------------------------------
4th / 5th / 6th / 7th GENERATION MODELS

* Make sure the Plasma and the Media Box are in standby.
* Using the remote control:
* Press {DISPLAY} button (just press, do not hold) and wait 3 seconds.
* Press {LEFT} {UP} {LEFT} {RIGHT} {POWER} buttons.
* The Plasma will turn on with the "Information" page displayed.
* Press {MUTE} to move through the levels of menus:

INFORMATION
FUNCTION CHECK
COMMON ADJ
OPTION
INITIALIZE

* Press the {DOWN} button to move through individual menus.
* To exit, power it down.
------------------------------------------------------
3rd GENERATION MODELS

* Power Down at the panel.
* Hold down {INPUT} & {VOL+} buttons on the panel.
* Turn on the Plasma at the panel.
* The service menu will come up.
* Scroll down using the arrow keys.
* To exit, power it down.
------------------------------------------------------------

RCA GE Proscan
1.
* Turn the TV off.
* Press simultaneously the {MENU} {VOL -} {CH -} buttons for about 8-10 seconds.
* The TV will turn on with the Service Menu displayed.
* Press the {POWER} button to exit.

2.
* Turn the TV off.
* Press and hold the {VOL -} & {CH -} buttons on the TV.
* Release both buttons when the green power light comes on.
* The TV will turn on with the Service Menu displayed.
* Press the {POWER} button to exit.

3.
To enter service mode, push and hold the {MENU} button on the set.
While holding, press and release the {POWER} button,
then press and release the {VOL +} button.

You will now have some information on the screen: "P0 V0"

To actually be able to change these values, you must push {VOL +} on the remote so the information reads V76. Then pushing on the Channel +/- will change the "P" value.

P1 - 3 are error codes. If there is a problem with the set that can be self-diagnosed, the "V" will report the code. These codes are available in the RCA repair manual.

P4 - 7 control the horizontal size, shift, vertical size and shift.

4.
On the front panel (FPA) of the F38310, simultaneously and quickly press the {CH -} & {DIRECTV} buttons. If successful, you should have displayed on the bottom of the screen:
Version Number: XX.XX P:0 V:0
(Note: Modifications to the parameters and values can be performed using the remote at this point. The remote must be in TV mode. To be sure, cover the IR bulb on the remote and depress the {TV} button, then you can use the remote for adjustments.)
Before adjustments can be performed, you must enter the password code to enable the FPA (or remote) for access. Use the {VOL +) button to change V:0 to V:76. Once this is done, you can now change the parameter setting for the desired function.
Be sure to write down the V: settings PRIOR to making changes in the event you need to revert.
---------------------------------------------------------------
SAMSUNG
1.
# Turn on the TV on and select the input that you want to adjust.
# Turn the display off.

# In quick sequence on the remote press:
{MUTE} {1} {8} {2} {POWER} buttons.

# The TV will turn On with the Service Menu displayed.
ADJUSTMENT - TEST PATTERN - SET OPTION BYTE - FACTORY RESET

# Select the function and use the {VOL+} button to enter.
# Save settings and exit by pushing {MUTE} twice then {POWER}.

2.
* With the TV in standby, press the {INFO} {MENU} {MUTE} {POWER} buttons on the remote.
* The TV will turn On with the Service Menu displayed.
* Press the {POWER} button to exit the Service Menu.

3.
* With the TV in standby, press the
{DISPLAY} {P.STD} {MUTE} {POWER} on the remote.
* The TV will turn On with the Service Menu displayed.
* Use the {CH+} {CH -} buttons to select items.
* Use the {VOL+} {VOL -} buttons to adjust.
* Press the {POWER} button to exit the Service Menu.

4.
* With the TV in standby, press the
{P.STD} {HELP} {SLEEP} {POWER} buttons on the remote.
or
{P.STD} {MENU} {SLEEP} {POWER} buttons on the remote.
* The TV will turn On with the Service Menu displayed.
* Use the {CH+} {CH -} buttons to select items.
* Use the {VOL+} {VOL -} buttons to adjust.
* Press the {POWER} button to exit the Service Menu.

5.
* With the TV in standby, press the
{SLEEP} {P.STD} {MUTE} {POWER} on the remote.
* The TV will turn On with the Service Menu displayed.
* Use the {CH+} {CH -} buttons to select items.
* Use the {VOL+} {VOL -} buttons to adjust.
* Press the {POWER} button to exit the Service Menu.

---------------------------------------------------------------
SANYO
1.
* Unplug the power cable.
* Press and hold the {MUTE} button on the remote control while plugging the power cable back into the outlet.
* Keep pressing the {MUTE} button until the TV powers on with the Service Menu displayed.
* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.
* Some menus might have sub-addresses. Use the numeric buttons {0} to {7} to adjust sub-item data.
* Press the {MENU} button or turn the TV off to exit.

2.
* Unplug the power cable.
* Press and hold the {VOL -} button on the TV
while plugging the power cable back into the outlet.

* Keep pressing the {VOL -} button until
the TV powers on with the Service Menu displayed.

* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.

* Some menus might have sub-addresses. Use the
numeric buttons {0} to {7} to adjust sub-item data.

* Press the {MENU} button or turn the TV off to exit.

SANYO PROJECTORS

1.
* Press and hold the {MENU} and {INPUT} buttons on the projector simultaneously for 5 seconds.
or
Press and hold the {MENU} button for 20 seconds.

* The "S" mark appears on the screen.

* While the "S" is being displayed, press and hold the {UP} and {DOWN} buttons on the projector
or
{SCREEN} button on the remote for more than 3 seconds.

* The Service Menu will be displayed.
* Adjust service data using the following control buttons:
{OK} ................ A group number increases.
{MENU} ............ A group number decreases.
{UP} ................ An item number increases.
{DOWN} .......... An item number decreases.
{RIGHT} .......... An adjustment value increases.
{LEFT} ............ An adjustment value decreases.
* To quit the service mode, press the "POWER ON/OFF" button only once on the projector or the remote control.

2.
* Factory Menu Access:
Press and hold the {SELECT} and {INPUT} buttons on the Projector at the same time for about 10 seconds.
* The Factory Menu will be displayed.
* Service Menu Access:
Press and hold the {MENU} and {INPUT} buttons on the Projector at the same time for about 10 seconds.
* The Service Menu will be displayed.
* Use the {UP} {DOWN} {LEFT} {RIGHT} buttons to move through menus and change values.
* To exit, turn the Projector Off.

3.
* Press & hold the {MENU} button on the Projector for about 10 seconds.
* The Service Menu will be displayed.
* Use the {UP} {DOWN} {LEFT} {RIGHT} buttons to move through menus and change values.
* To exit, turn the Projector Off.

SANYO
1.
* Unplug the power cable.
* Press and hold the {MUTE} button on the remote control while plugging the power cable back into the outlet.
* Keep pressing the {MUTE} button until the TV powers on with the Service Menu displayed.
* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.
* Some menus might have sub-addresses. Use the numeric buttons {0} to {7} to adjust sub-item data.
* Press the {MENU} button or turn the TV off to exit.

2.
* Unplug the power cable.
* Press and hold the {VOL -} button on the TV
while plugging the power cable back into the outlet.

* Keep pressing the {VOL -} button until
the TV powers on with the Service Menu displayed.

* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.

* Some menus might have sub-addresses. Use the
numeric buttons {0} to {7} to adjust sub-item data.

* Press the {MENU} button or turn the TV off to exit.

SANYO PROJECTORS

1.
* Press and hold the {MENU} and {INPUT} buttons on the projector simultaneously for 5 seconds.
or
Press and hold the {MENU} button for 20 seconds.

* The "S" mark appears on the screen.

* While the "S" is being displayed, press and hold the {UP} and {DOWN} buttons on the projector
or
{SCREEN} button on the remote for more than 3 seconds.

* The Service Menu will be displayed.
* Adjust service data using the following control buttons:
{OK} ................ A group number increases.
{MENU} ............ A group number decreases.
{UP} ................ An item number increases.
{DOWN} .......... An item number decreases.
{RIGHT} .......... An adjustment value increases.
{LEFT} ............ An adjustment value decreases.
* To quit the service mode, press the "POWER ON/OFF" button only once on the projector or the remote control.

2.
* Factory Menu Access:
Press and hold the {SELECT} and {INPUT} buttons on the Projector at the same time for about 10 seconds.
* The Factory Menu will be displayed.
* Service Menu Access:
Press and hold the {MENU} and {INPUT} buttons on the Projector at the same time for about 10 seconds.
* The Service Menu will be displayed.
* Use the {UP} {DOWN} {LEFT} {RIGHT} buttons to move through menus and change values.
* To exit, turn the Projector Off.

3.
* Press & hold the {MENU} button on the Projector for about 10 seconds.
* The Service Menu will be displayed.
* Use the {UP} {DOWN} {LEFT} {RIGHT} buttons to move through menus and change values.
* To exit, turn the Projector Off.
-------------------------------------------------------

SHARP
1.
* Unplug the TV
* Press and hold the {VOL -} & {CH+} buttons.
* While holding the above buttons, plug in the TV.
* The TV will turn on with the Service Menu displayed.

* There are 5 category menus:
Deflection - Signal - Feature - Fix Value - EEPROM
* Use {CH+} {CH -} buttons to select a category.
Note: Not all models will have 5 categories.
Some will jump to 'Signal' category.

* Use {VOL+} to enter the category.
* Use {CH+} {CH -} buttons to select the item to be adjusted.
* Use {VOL+} {VOL -} buttons to adjust the value.
* Turn the set off to exit the Service Menu.

SHARP LCD TVs :

* While the LCD is on, unplug the power cable.
* Then while pressing the {INPUT} & {VOL -} buttons on the remote, plug the power cable back into the outlet.
* When it powers up you will see a little "k" appear in brackets.
* Then on the TV, press and hold {VOL -} & {CH -} down and release.
* The Service Menu will be displayed.
* Use {CH+} {CH -} buttons to navigate
* Use {VOL+} {VOL -} buttons to adjust the value.
* Turn the set off to exit the Service Menu.

SHARP PROJECTORS:
1.
* Press {INPUT} {UP} {DOWN} {ENTER} {ENTER} {MENU}
buttons on the back of the Projector.
* Now use the remote control to navigate through menus.
* To exit the Service Menu:
Press {INPUT} {UP} {DOWN} {ENTER} {ENTER} {MENU}
buttons again on the back of the Projector.

2.
* Press {UP} {UP} {DOWN} {DOWN} {RIGHT} {LEFT} {ENTER}
buttons on the Projector (or remote ?).
* The Service Menu will be displayed.
* To exit, turn the Projector Off.

--------------------------------------------------------------------
SONY
# Using the remote control:
# Turn the TV off.
# Press {DISPLAY} {5} {VOL+} {POWER ON} buttons.
or
Press {DISPLAY} {5} {POWER ON} buttons.
# The Service Menu will be displayed.
# Use numbers {1} and {4} to select the item to adjust.
# Use numbers {3} and {6} to adjust the value of the data.
# Press {MUTE} then {ENTER} to save new settings.
# The words "WRITE" in red will show up in the upper right corner if saved.
# Turn the TV off to exit the service menu.

SONY PROJECTORS :


* Service Menu :
* Using the remote control
* Press {ENTER} {ENTER} {UP ARROW} {DOWN ARROW} {ENTER}.
* Then {UP ARROW} when it asks: "Do you want to enter the Service Mode?".

* Factory Mode :
* Using the remote control
* Press {ENTER} {ENTER} {LEFT ARROW} {ENTER}.
* Then {UP ARROW} when it asks: "Do you want to enter the Factory Mode?".

* Any additional menus usually pop up under the main INFORMATION menu.
----------------------------------------------
* Access "Menu" and make sure "Status" is On.
* Exit the "Menu".

* Service Menu :
* Using the remote control
* Press {ENTER} {ENTER} {UP ARROW} {DOWN ARROW} {ENTER}.
* Select "Yes" when it asks: "Do you want to enter the Service Mode?".

* Factory Mode :
* Using the remote control
* Press {ENTER} {ENTER} {LEFT ARROW} {ENTER}.
* Select "Yes" when it asks: "Do you want to enter the Factory Mode?".
-----------------------------------------------------
SYLVANIA
* Press {0} {6} {2} {5} {9} {7} {INFO+} on the remote.
or
* Press {0} {6} {2} {5} {9} {7} {STATUS} on the remote.
or
* Press {0} {6} {2} {5} {9} {7} {MENU} on the remote.
or
* Press {0} {6} {2} {5} {9} {6} {INFO+} on the remote.
or
* Press {0} {6} {2} {5} {9} {6} {STATUS} on the remote.
or
* Press {0} {6} {2} {5} {9} {6} {MENU} on the remote.
or
* Press {0} {6} {1} {5} {9} {6} {MENU} on the remote.
or
* Press {0} {6} {1} {5} {9} {7} {MENU} on the remote.
or
* Press {1} {6} {2} {5} {9} {6} {MENU} on the remote.
or
* Press {1} {6} {2} {5} {9} {6} {STATUS} on the remote.
-----------------------------------------------
* With the TV off:

* Press {0} {6} {2} {5} {9} {6} {STATUS} on the remote.

* Turn the TV off to exit the Service Menu.


THOMSON
1.
* With the TV in standby:
* Press and hold the {VOL -} & {PRG -} buttons on the TV.
* Keep both buttons pressed until the TV turns On with the Service Menu displayed.
* To exit, turn the TV Off.

2.
* While the TV is On, press the {POWER} button on the remote control to put TV in standby.
* Turn the TV Off using the {POWER} button on the TV.
* Using the buttons on the TV:
* Turn the TV On while pressing the {PRG -} & {VOL -} buttons
* The Service Menu will be displayed.
* To exit, turn the TV Off.


TOSHIBA

1.
# Turn the TV on.
# Press the {MUTE} button three times on the remote.
# Press the {MUTE} button again on the remote and hold.
# Then press the {MENU} button on the TV's front panel.
# Release both buttons
# There should be a letter "S" on the upper right of the screen.
# Press the {MENU} button on the TV's front panel again.

# You are now in Service Menu.
# Use the {CH+} or {CH-} buttons to select the item.
# Use the {VOL+} and {VOL -} buttons to adjust the value.
# Turn the set off to exit the Service Menu.

2.
* Turn the TV on.
* Press and hold the {VOL-} button on the TV.
* Press and hold the {9} button on the remote.
* The Service Menu will be displayed.

* Use the {CH+} or {CH-} buttons to select the item.
* Use the {VOL+} and {VOL -} buttons to adjust the value.
* Turn the set off to exit the Service Menu.
----------------------------------------
TOSHIBA LCD's :


* Press the {MENU} button on the remote.
* Highlight the "Picture" icon.
* Press the {9} {3} {0} {1} buttons
on the remote control.

* The Service Menu will be displayed
with the following Modes:

"Options" - "Adjustments" - "Selections"

* Use the {OK} button to access and
navigate through these Modes.

* To change values use {VOL +} {VOL-) {P+} {P-}
* To exit, press the {MENU} button.
--------------------------------------------------------
ZENITH

1.
Service Menu #1

Press and hold the {MENU} button on the remote and
the {MENU} button on the TV at the same time,
until the first Service Menu is displayed.

* Service Menu #2

Repeat the above sequence:
Press and hold the {MENU} button on the remote and
the {MENU} button on the TV at the same time,
until the second Service Menu is displayed.


2.
* Press and hold the {MENU} button on the remote
and the {MENU} button on the TV at the same time

* If a password screen comes up:

Press and hold the {MENU} button on the remote
and the {MENU} button on the TV at the same time
again, until the Service Menu is displayed.

3.
* Press and hold the {MENU} button ON THE REMOTE
until a 4-digit password screen is displayed.

* Then try any of the following codes to
access the Service Menu:

{0} {0} {0} {0}
{7} {7} {7} {7}
{8} {7} {4} {1}

4.
* Press and hold the {MENU} button ON THE REMOTE.
(The menu on the screen will disappear)

* Now Press and hold the {MENU} button ON THE PANEL.
* Keep both buttons pressed until the Service Menu is displayed, then release the 2 buttons.

* Using the remote control buttons:

{MENU} = Toggles between two menu pages.
{UP} {DOWN} = Selects the item for adjustment.
{LEFT} {RIGHT} = Varies the value
{POWER} = Exit service mode and saves adjustments made.

5.
* Turn the TV on.
* Hold down the {MENU} button on remote until the on-screen menu
disappears or "Welcome Message" appears then release the {MENU}
button and within two (2) seconds press the following five buttons:

{9} {8} {7} {6} {ENTER}
or
{9} {8} {7} {6} {DISPLAY}

* The Service Menu will be displayed.

* Using the remote control buttons:

{MENU} = Toggles between two menu pages.
{UP} {DOWN} = Selects the item for adjustment.
{LEFT} {RIGHT} = Varies the value
{POWER} = Exit service mode and saves adjustments made.

Vizio
With power off, hold Ch UP and Ch Down together for 10 seconds.
While still holding Ch up and down together, push power, then let go.
Select OSD button, there should be a letter in the lower right hand corner of the menu.
Then hold OSD and Mute/Exit buttons together until factory menu comes up. Make adjustments with remote, select exit, then turn off power to save the adjustments.

Hitachi
RPTVs :

F59 SERIES

* Press and hold the {MENU} button on the TV.
* Then press the {MENU} {8} {SELECT} buttons on the remote.
* To exit, press the {MENU} button on the TV or
the {EXIT} button on the remote control.

DCAM Mode:

* Using the remote control:
* Hold down the {TV} button.
* Press the {MENU} button.
* Press the {INFO} button.
* Release the {TV} button.
* Remote Control Key Functions When In DCAM Mode:

{INPUT} ............. Blue (13x9 adjust)
{ASPECT} ............ ROM Write
{DAY/NIGHT} ......... ROM Read
{MENU} .............. Remove Color
{EXIT} .............. Cross Hatch/Video Mode
{INFO} .............. Green
{GUIDE} ............. Calculation
{2} ................. Cursor UP
{5} ................. Cursor DOWN
{6} ................. Cursor RIGHT
{4} ................. Cursor LEFT
{0} ................. RED (7x5 Adjust)
{STOP} .............. Initialize
{PLAY} .............. Raster Position
{FAST FORWARD} ...... Phase

To Exit The DCAM Mode:

* Press and hold the {TV} button.
* Press the {0} button.
* Press the {1} button.
* Release the {TV} button.

HITACHI PROJECTORS :

* Press the {MENU} & {RESET} buttons and then press
the {RESET} button again and hold it for at least 5 seconds.
* The Service Menu will be displayed.
* To exit, turn the Projector Off.


HITACHI MISC :

1.
* Turn the TV on.
* Press the {MENU} {MENU} {8} {SELECT} buttons on the remote.
* The Service Menu will be displayed.
* Use the {UP} {DOWN} buttons to select items.
* Use the {LEFT} {RIGHT} to change the data.
* Press the {EXIT} button to exit the Service Menu.

2.
* Turn the TV off.
* Press and hold the {INPUT} button on the TV then press {POWER}.
* Hold both buttons until the TV powers on
with the Service Menu displayed.
* Use the {UP} {DOWN} buttons to select items.
* Use the {LEFT} {RIGHT} to change the data.
* Press the {EXIT} button to exit the Service Menu.

3.
* Turn the TV off.
* Press {POWER} & {INPUT} buttons on the TV for more than 3 sec.
* The Service Menu will be displayed.
* The letter "P" indicates picture and "A" indicates audio.
* Use the {UP} {DOWN} buttons to select items.
* Use the {LEFT} {RIGHT} to change the data.
* Press the {EXIT} key to exit the Service Menu.

THANKS SIR MY LCD TV SAMSUNG NOT SOUND

I TRY WITH
Vizio Service Menu Method 2
1. Turn The TV off.
2. Press and hold the {CH +} & {CH -} buttons on the TV.
3. Then press and hold the {POWER} button on the TV.
4. Keep all three buttons pressed for few seconds.
5. Now press the {MENU} button on the remote.

Tv jvc lcd hd don't turn on blue liht blinking

For Models: LT-32E479, LT-32EM49, LT-32P679, LT-42X579, LT-42SL89, LT-42EM59, LT-42P789, LT-46SL89, LT-47X579, LT-47EM59, LT-47P789, LT-52X579, LT-52P789 After the TV is powered ON, no video appears and the power LED at the lower left of the TV begins flashing:
Restore the TV's normal function by changing the operating mode. Please follow the procedure below.
PROCEDURE
• 1. Unplug the TV or remove AC power from the TV
• 2. Count to ten, then plug in the TV
• 3. Locate the [Menu], [Vol-] and [Power] button on the TV's side panel
• 4. Using the buttons on the TV's Side Panel, press and hold both the [Menu] and [Vol-] buttons.
• 5. While holding those buttons, press and release the [Power] button one time and count to 3 before releasing the [Menu] and [Vol-] buttons.
• 6. The TV's lower left Blue Power LED will come ON.
• 7. Wait 30 seconds. Confirm that the blue LED on the Lower Left of the TV (not the iPod dock for iPod models) has remained ON during this time.
a. The TV may have turned ON. If so,continue at step 12 b. If the Blue LED on the TV's Lower Left corner remained ON, continue to step 8.
• 8. After confirming that the Blue LED is ON, unplug the TV or remove the AC power from the TV.
a. If the Blue LED on the TV's Lower Left corner is flashing, restart the procedure from step 3
• 9. Count to 10, then plug in the TV
• 10. The TV power should automatically come ON but no picture will appear. Only the blue power LED will be ON
• 11. Wait 40 seconds and the TV picture should appear
• 12. When the TV picture appears, you may begin normal use of the TV. (procedure is complete)


"OKI" tv brand (also "Precision" brand) SERVICE MENU

1 "MENU" in r/c
2 press 4725 4725 (twice)
3 In Service menu go to "DIAGNOSTIC"
4 Then "FACTORY RESET" and press "OK" in r/c


Continut sponsorizat

INFORMATIV Re: O mica baza de date cu modalitati de intrare in SM



Vezi subiectul anteriorSusVezi subiectul urmator
Permisiunile acestui forum:
Nu puteti raspunde la subiectele acestui forum